Loading...
4 results
Search Results
Now showing 1 - 4 of 4
- Neutral Axis Depth versus Ductility and Plastic Rotation Capacity on Bending in Lightweight-Aggregate Concrete BeamsPublication . Bernardo, Luís; Nepomuceno, Miguel; Pinto, HugoThis article presents an experimental study on the evolution of the neutral axis depth at failure in the critical section with the flexural ductility and plastic rotation capacity of reinforced concrete (RC) lightweight-aggregate concrete (LWAC) beams. For this, the results of a previous experimental program involving RC LWAC beams tested in flexure until failure are used. The variable studies were the concrete compressive strength (between 22.0 and 60.4 MPa and dry density between 1651 and 1953 kg/m3) and the longitudinal tensile reinforcement ratio (between 0.13% and 2.69%). The flexural ductility and the plastic rotation capacity of the RC LWAC beams are characterized by a ductility index and a plastic trend parameter, respectively. The influence of the variable studies, as well as the relation of the flexural ductility and plastic rotation capacity with the values for the neutral axis depth at failure are analyzed and discussed. Some conclusions are drawn which can be useful for the design of RC LWAC beams for flexure. In particular, it is shown that the practical rule of limiting the neutral axis depth at failure to ensure ductile behavior, as used in normal-weight aggregate concrete beams, is also valid for RC LWAC beams.
- Plastic rotation capacity of lightweight-aggregate concrete beamsPublication . Bernardo, Luís; Nepomuceno, Miguel; Pinto, HugoThis article describes a study on the plastic behaviour of lightweight-aggregate concrete beams. The experimental results of nineteen simply supported beams previously tested by the authors were used in this study. The experimental plastic rotation capacity of the tested beams was characterized by a parameter called Plastic Trend Parameter (PTP). The main variables studied were the concrete compressive strength and the longitudinal tensile reinforcement ratio. It was found that plastic rotation capacity slightly increases as the concrete compressive strength increases. An appropriate range for the longitudinal tensile reinforcement ratio to ensure plastic rotation capacity is proposed. The results of this study were also compared with the requirements from some codes of practice. From this analysis, it was shown that ACI Code requirements give more guaranties as far as plastic rotation capacity is concerned, when compared with European codes.
- Effective torsional strength of axially restricted RC beamsPublication . Taborda, Cátia S. B.; Bernardo, Luís; Gama, JorgeIn a previous study, design charts where proposed to help the torsional design of axially restricted reinforced concrete (RC) beams with squared cross section. In this article, new design charts are proposed to cover RC beams with rectangular cross section. The influence of the height to width ratio of the cross section on the behavior of RC beams under torsion is firstly shown by using theoretical and experimental results. Next, the effective torsional strength of a reference RC beam is computed for several values and combinations of the study variables, namely: height to width ratio of the cross section, concrete compressive strength, torsional reinforcement ratio and level of the axial restraint. To compute the torsional strength, the modified Variable Angle Truss Model for axially restricted RC beams is used. Then, an extensive parametric analysis based on multivariable and nonlinear correlation analysis is performed to obtain nonlinear regression equations which allow to build the new design charts. These charts allow to correct the torsional strength in order to consider the favourable influence of the compressive axial stress that arises from the axial restraint.
- Flexural ductility of lightweight-aggregate concrete beamsPublication . Bernardo, Luís; Nepomuceno, Miguel; Pinto, HugoThis paper describes an experimental study on the flexural ductility of lightweight-aggregate concrete beams including concretes with compressive strengths between 22.0 and 60.4 MPa and dry densities between 1651 and 1953 kg/m3. Nineteen simply supported beams were tested until failure. Two symmetrical concentrated loads were applied at approximately one third of the span. Ductility was studied by defining ductility indexes. The main variables are the concrete compressive strength and the longitudinal tensile reinforcement ratio. It is shown that the parameter with higher influence on ductility is the longitudinal tensile reinforcement ratio. The test results are also compared with the requirements from some codes of practice. It is shown that ACI Code requirements give more guaranties as far as ductility is concerned, when compared with European codes.