PHARMACOLOGICALLY ACTIVE BIOADHESIVE DESIGNED FOR WOUND CLOSURE

Funder

Organizational Unit

Publications

Development of UV cross-linked gelatin coated electrospun poly(caprolactone) fibrous scaffolds for tissue engineering

Publication . Correia, Tiago R.; Ferreira, Paula; Vaz, Rita; Alves, Patrícia; Figueiredo, Margarida; Correia, Ilídio Joaquim Sobreira; Coimbra, Patrícia

Cardiovascular disease is the leading cause of morbidity and mortality among industrialized countries. Vascular grafts are often required for the surgical treatments. Considering the limitations associated with the use of autografts and with the currently available synthetic materials, a growing demand in tissue engineered vascular grafts has been registered. During the work here described, electrospinning technique was used to prepared fibrous matrices to be applied as vascular implants. For that purpose, electrospun polycaprolactone (PCL) fibrous mats were produced and afterwards coated with different hydrogel formulations based in photocrosslinkable gelatin (GelMA) and the macromers poly(ethylene glycol) acrylate (PEGA) and poly(ethylene glycol) diacrylate (PEGDA). These were further photocrosslinked under UV irradiation using Irgacure® 2959 (by BASF) as the photoinitiator. The suitability of the coated scaffolds for the intended application, was evaluated by assessing their chemical/physical properties as well as their interaction with blood and endothelial cells.

2016-05-13Journal article

Restricted access

Photocurable bioadhesive based on lactic acid

Publication . Marques, Dina; Santos, João; Ferreira, Paula; Correia, Tiago R.; Correia, Ilídio Joaquim Sobreira; Gil, Maria; Baptista, Cristina Maria dos Santos Gaudêncio

Novel photocurable and low molecular weight oligomers based on l-lactic acid with proven interest to be used as bioadhesive were successfully manufactured. Preparation of lactic acid oligomers with methacrylic end functionalizations was carried out in the absence of catalyst or solvents by self-esterification in two reaction steps: telechelic lactic acid oligomerization with OH end groups and further functionalization with methacrylic anhydride. The final adhesive composition was achieved by the addition of a reported biocompatible photoinitiator (Irgacure® 2959). Preliminary in vitro biodegradability was investigated by hydrolytic degradation in PBS (pH = 7.4) at 37 °C. The adhesion performance was evaluated using glued aminated substrates (gelatine pieces) subjected to pull-to-break test. Surface energy measured by contact angles is lower than the reported values of the skin and blood. The absence of cytoxicity was evaluated using human fibroblasts. A notable antimicrobial behaviour was observed using two bacterial models (Staphylococcus aureus and Escherichia coli). The cured material exhibited a strong thrombogenic character when placed in contact with blood, which can be predicted as a haemostatic effect for bleeding control. This novel material was subjected to an extensive characterization showing great potential for bioadhesive or other biomedical applications where biodegradable and biocompatible photocurable materials are required.

2016-01-01Journal article

Restricted access

Coaxial electrospun PCL/Gelatin-MA fibers as scaffolds for vascular tissue engineering

Publication . Coimbra, Patrícia; Santos, Patrícia; Alves, Patrícia; Miguel, Sónia P.; Carvalho, Marco António Paulo de; Sá, Kevin; Correia, Ilídio Joaquim Sobreira; Ferreira, Paula

Coaxial electrospinning is a technique that allows the production of nanofibers with a core–shell structure. Such fibers present several advantages as materials for the preparation of scaffolds, namely due to the possibility of combining a core with the desired mechanical properties with a shell prepared from biocompatible materials that will establish proper interactions with the host. Herein, core-shell fibrous meshes, composed of a polycaprolactone (PCL) core and a functionalized gelatin shell, were prepared by coaxial electrospinning and then photocrosslinked under UV light aiming to be used in vascular tissue regeneration. The suitability of the meshes for the pretended biomedical application was evaluated by assessing their chemical/physical properties as well as their haemo and biocompatibility in vitro. The obtained results revealed that meshes’ shell prepared with a higher content of gelatin showed fibers with diameters presenting a unimodal distribution and a mean value of 600 nm. Moreover, those fibers with higher content of gelatin also displayed lower water contact angles, and therefore higher hydrophilicities. Such features are crucial for the good biologic performance displayed by these meshes, when in contact with blood and with Normal Human Dermal Fibroblasts cells.

2017-07-26Journal article

Restricted access

Photocrosslinkable electrospun fiber meshes for tissue engineering applications

Publication . Ferreira, Paula; Santos, Patrícia; Alves, P.; Carvalho, Marco António Paulo de; Sá, Kevin; Miguel, Sónia P.; Correia, Ilídio Joaquim Sobreira; Coimbra, Patrícia Manuela Almeida

Electrospun polymeric meshes are known to exhibit promising properties for the regeneration of several soft tissues. Herein, electrospun polymeric meshes were prepared from blends of polycaprolactone and functionalized gelatin. The meshes were then photocrosslinked under UV light using Irgacure® 2959 as the photoinitiator, aiming to improve membranes’ stability in biological fluids. Moreover, meshes suitability to be used as vascular grafts was evaluated by characterizing their chemical/physical properties as well as their haemo and biocompatibility in vitro. The obtained results show that the blended polymeric meshes are biodegradable and those with a higher content of gelatin display a lower water contact angle. Blood compatibility studies showed that the photocrosslinked membranes are haemocompatible, i.e. they display low values of thrombogenicity and do not trigger any haemolytic effect. Also, Normal Human Dermal Fibroblasts cells were incubated in the presence of the produced membranes and they were able to adhere and proliferate, thus revealing the biocompatibility of the photocrosslinked meshes.

2017-10-12Journal article

Restricted access

Functionalization and photocuring of an L-lactic acid macromer for biomedical applications

Publication . Marques, Dina; Santos, João; Ferreira, Paula; Correia, Tiago R.; Correia, Ilídio Joaquim Sobreira; Gil, Maria; Baptista, Cristina Maria dos Santos Gaudêncio

L-lactic acid was the starting material for obtaining bioahesives. Reaction with 1,4-butanediol provided a telechelic lactic acid prepolymer with hydroxyl end groups further functionalized with 2-isocyanatoethyl methacrylate. Films were produced upon UV irradiation, 2 min, after addition of Irgacure 2959. This was a solvent and catalyst free process. Thermal characterization of films confirmed stability at physiological temperature, enabling photocuring. Adhesion properties were assessed with good results. In vitro degradation tests showed moderate hydrolytic instability dependent on thickness. SEM images revealed a uniform and compact structure. Thrombosis tests confirmed the materials’ thrombogenicity while biocompatibility experiments showed fibroblast viability and antimicrobial behavior.

2016-04-07Journal article

Restricted access