Intelligent Systems for Structures Strengthening and Monitoring

Funder

Organizational Unit

Publications

Smart Textiles for Strengthening of Structures

Publication . Górski, Marcin; Krzywoń, Rafał; Dawczyński, Szymon; Szojda, Leszek; Salvado, Rita; Lopes, Catarina; Araújo, Pedro; Velez, Fernando J.; Gomes, João Castro

This paper presents results of mechanical tests on a prototype of an innovative structural strengthening in form of self-monitoring fabric. Smart textile employs carbon fibers conductivity for measuring strains while monitoring changes of electric resistance under increasing load. A general solution was tested in a series of calibrating tests on strengthening of small size concrete slabs. Promising results of simple specimen, has encouraged the research team to perform the next tests using mastered carbon fibre reinforced fabric. Main tests were performed on natural scale RC beam. Smart textile proved its efficiency in both: strengthening and monitoring of strains during load increase. New strengthening proposal was given 10% increase of loading capacity and the readings of strain changes were similar to those obtained in classical methods. In order to calibrate the prototype and to define range limits of solution usability, textile sensor was tested in areas of large deformations (timber beam) and as well as very small strains (bridge bearing block). In both cases, the prototype demonstrated excellent performance in the range of importance for structural engineering. This paper also presents an example of use of the smart strengthening in situ, in a real life conditions.

2016-09Journal article

Open access

Block acknowledgment mechanisms for the optimization of channel use in wireless sensor networks

Publication . Barroca, Norberto; Velez, Fernando J.; Chatzimisios, Periklis

One of the fundamental reasons for the IEEE 802.15.4 standard Medium Access Control (MAC) inefficiency is overhead. The current paper proposes and analyses the Sensor Block Acknowledgment MAC (SBACK-MAC) protocol, a new innovative protocol that allows the aggregation of several acknowledgment responses in one special BACK Response packet. Two different solutions are addressed. The first one considers the SBACK-MAC protocol in the presence of BACK Request (concatenation) while the second one considers the SBACK-MAC in the absence of BACK Request (piggyback). The proposed solutions address a distributed scenario with single-destination and single-rate frame aggregation. The throughput and delay performance is mathematically derived under ideal conditions (a channel environment with no transmission errors). The proposed schemes are compared against the basic access mode of IEEE 802.15.4 through extensive simulations by employing the OM-NET++ simulator. We demonstrate that the network performance is significantly improved in terms of throughput and end-to-end delay.

2013-09Conference object

Open access

Carbon Fiber Epoxy Composites for Both Strengthening and Health Monitoring of Structures

Publication . Salvado, Rita; Lopes, Catarina; Szojda, Leszek; Araújo, Pedro; Górski, Marcin; Velez, Fernando J.; Castro-Gomes, João; Krzywon, Rafal

This paper presents a study of the electrical and mechanical behavior of several continuous carbon fibers epoxy composites for both strengthening and monitoring of structures. In these composites, the arrangement of fibers was deliberately diversified to test and understand the ability of the composites for self-sensing low strains. Composites with different arrangements of fibers and textile weaves, mainly unidirectional continuous carbon reinforced composites, were tested at the dynamometer. A two-probe method was considered to measure the relative electrical resistance of these composites during loading. The measured relative electrical resistance includes volume and contact electrical resistances. For all tested specimens, it increases with an increase in tensile strain, at low strain values. This is explained by the improved alignment of fibers and resulting reduction of the number of possible contacts between fibers during loading, increasing as a consequence the contact electrical resistance of the composite. Laboratory tests on strengthening of structural elements were also performed, making hand-made composites by the “wet process”, which is commonly used in civil engineering for the strengthening of all types of structures in-situ. Results show that the woven epoxy composite, used for strengthening of concrete elements is also able to sense low deformations, below 1%. Moreover, results clearly show that this textile sensor also improves the mechanical work of the strengthened structural elements, increasing their bearing capacity. Finally, the set of obtained results supports the concept of a textile fabric capable of both structural upgrade and self-monitoring of structures, especially large structures of difficult access and needing constant, sometimes very expensive, health monitoring.

2015-03Journal article

Open access

Experimental Characterization of Wearable Antennas and Circuits for RF Energy Harvesting in WBANs

Publication . Saraiva, Henrique Morais; Borges, Luís M.; Pinho, Pedro; Gonçalves, Ricardo; Chavez-Santiago, Raul; Barroca, Norberto; Tavares, Jorge; Gouveia, Paulo T.; Carvalho, Nuno Borges; Balasingham, Ilangko; Velez, Fernando J.; Loss, Caroline; Salvado, Rita

Field trials have been performed in Covilhã to identify the spectrum opportunities for radio frequency (RF) energy harvesting through power density measurements from 350 MHz to 3 GHz. Based on the identification of the most promising opportunities, a dual-band printed antenna was conceived, operating at GSM bands (900/1800), with gains of 1.8 and 2.06 dBi, and efficiency varying from 77.6 to 82%, for the highest and lowest operating frequency bands, respectively. In this paper, guidelines for the design of RF energy harvesting circuits and choice of textile materials for a wearable antenna are briefly discussed. Besides, we address the development and experimental characterization of three different prototypes of a five-stage Dickson voltage multiplier (with and without impedance matching circuit) responsible for RF energy harvesting. All the three prototypes (1, 2 and 3) can power supply the sensor node for RF received powers of 2 dBm, -3 dBm and -4 dBm, and conversion efficiencies of 6, 18 and 20%, respectively.

2014-05Conference object

Open access

Block acknowledgment in IEEE 802.15.4 by employing DSSS and CSS PHY layers

Publication . Barroca, Norberto; Borges, Luís M.; Velez, Fernando J.; Chatzimisios, Periklis

The IEEE 802.15.4 standard has been widely accepted as the de facto standard for Wireless Sensor Networks (WSNs), since it provides ultra-low complexity, cost and energy consumption for low-data rate wireless connectivity. However, one of the fundamental reasons for the IEEE 802.15.4 Medium Access Control (MAC) inefficiency is overhead. In the context of our research, we demonstrate that WSNs may benefit from packet concatenation. In this paper we introduce and study the employment of a block acknowledgment mechanisms in order to achieve enhanced channel efficiency in IEEE 802.15.4 nonbeacon-enabled networks for both the Chirp Spread Spectrum (CSS) and Direct Sequence Spread Spectrum (DSSS) Physical (PHY) layers for the 2.4 Industrial, Scientific and Medical (ISM) frequency band. The proposal of the two new innovative MAC sublayer mechanisms can also be considered as a future possible contribution to the standard itself. The throughput and delay performance is mathematically derived under ideal conditions, (i.e., a channel environment without transmission errors). The performance of the proposed schemes is compared against the IEEE 802.15.4 standard through extensive simulations by employing the OMNeT++ simulator. We demonstrate that, for both PHY layers, the network performance is significantly improved in terms of throughput, end-to-end delay and bandwidth efficiency.

2014-12Conference object

Open access